230 x 76 x110mm. Of course, not everyone follows these measurements to the letter, but this is the ‘Australian Standard’.
These are bricks built to withstand saline (salty) environments and their exposure grading is determined by a lab test. They are recommended when building up to 1km from a surf coast or up to 100m from a non-surf coast.
Efflorescence is a fancy way of describing the white, salty powder that sometimes appears on bricks (usually from salts in cement and mortar). Fortunately, the powder is completely harmless and will usually weather away with time. You can brush it off, although it may return if the salt source is still active.
The most common mix is a) one part cement, b) one part lime and c) six parts sand (M3 1:1:6, though the 'Australian Standard’ lists 7 other mix options). Whichever mix you choose, however, we strongly recommend one containing lime as it makes the mortar more durable and less prone to cracks.
‘Thermal Lag’ is a term used to describe the way bricks both absorb and release heat slowly (hence the ‘lag’ part). It helps keep brick homes cooler in summer and warmer in winter.
The best time to clean brickwork is while it is being laid. Mortar smears should be cleaned as soon as possible using a scrubbing brush, running water and a sponge. If mortar hardens, acid cleaning can be used, but only as a last resort.
PGH bricks are made from clay, shale and other minerals that are moulded into the ‘brick’ shape then fired (cooked) at temperatures up to 1200°C.
Actually they’re better. Thanks to improved technology, not only are today’s bricks are stronger than ever before, they also come in a wider variety of colours and textures.
A brick’s ‘face’ is the side designed to be seen. Most bricks only have one ‘face’ and therefore it is important that bricklayers lay them correctly.
Bricks with holes (or ‘extruded bricks’) are manufactured with these holes to ensure that when they are fired, they cook evenly. The holes, up to 30% of material thickness, have no effect on the insulation or fire resistance of the brick (as confirmed by Australian Standards).
Yes. In fact, bricks are one of the few construction materials that can. The only circumstance where a brick might not be suitable for reuse is if that brick was not manufactured for a saline environment or wasn’t intended to be a ‘face’ brick.
Absolutely. Bricks have a remarkably low environmental cost, an extraordinary long life. Their thermal mass even reduces the need for artificial heating and cooling.
When designing energy efficient buildings, the architect and consulting engineers need to be able to calculate the heat loss or gain of materials used to construct the buildings. This is why building materials are categorises into 3 categories: Light (L), Medium (M) and Dark (D). Light coloured being a low solar absorptance and Dark coloured being a higher solar absorptance.
| Arris | The sharp edge formed by any two surfaces meeting at an angle. |
| Banding | Brickwork, normally of a contrasting colour or texture, one or more courses high. |
| Batch | The specific production run of bricks or pavers. |
| BCA | Building Code of Australia. |
| Bevelled | The edges of the face of some bricks are bevelled or sloped, providing a softer decorative effect. |
| Blends | A mixture of two or more brick types. |
| Brick sand | Also called 'brickies sand'. Common term for sand used for making mortar. Colour can vary by region and therefore impact the mortar colour achieved. |
| Brick Veneer | Construction where a timber or metal frame is covered with a lining material for internal walls and a single leaf or layer of brickwork forms the exposed exterior of the building. |
| Burns | An aesthetic treatment during firing to create light to dark blushes. Also known as 'flashing'. |
| Commons | Bricks that are to be covered up, or used where they are not seen. |
| Crazing | Very fine non-structural cracks on the face of the brick. |
| Damp course | A course, or layer, of impervious material in a wall or floor to prevent the migration of moisture. Also called 'damp-proof course' or DPC. The Building Code of Australia requires the DPC to visibly extend beyond the mortar. |
| Dry Pressed bricks | Solid bricks that are made by pressing clay into individual moulds. |
| Efflorescence | A white or sometimes coloured powder, often furry in appearance, that can form on the surface of brickwork. This is caused by salt deposits in the mortar and can easily be brushed off. It disappears over time. |
| Face | The long surface of a brick to be exposed in a wall. |
| Flashing | A method used during firing to create light to dark blushes or areas of deepened colour. |
| Footings or foundations | The base of a building, usually concrete, designed to transfer loads to the ground. |
| Frit | A glass substance melted onto bricks to create glossy spots. |
| Full or double brick | Construction where most of the external and internal walls are made of brick. The external walls are usually composed of two layers of brick, with a 50mm cavity between them. |
| Hearting | A red, or sometimes orange, aesthetic burn on the brick face. |
| Joint | How the layer of mortar between two bricks is finished. |
| Monochromatic | Containing only one colour. |
| Mortar | A mixture of lime, cement, sand and water. |
| Owner builder | A builder who controls the building process of their own home, managing the project and coordinating subcontractors. |
| Pack | A package or bundle of bricks or pavers prepared for delivery. |
| Rockface | A brick face texture where the face of a brick is chipped off. |
| Slurry | A texturing process where a coloured solution is applied and kiln fired into the body of the brick to create a permanent, ceramic finish. |
| Tumbled or rumbled | A term used to describe the distortion of brick edges. |
| Vanadium | A form of efflorescence derived from yellow or green salt deposits that is particularly visible on light-coloured bricks. |
| Weighted Sound Reduction Index (Rw) | A measure of the reduction in sound level passing through a wall. |
| Wirecut bricks | Also called extruded bricks, these are bricks with holes made by forcing a column of clay through a die, and then cutting with a wire. |
